Bishop I Italeri I 1/72

After spending some time building 1/35 scale models, I went back to 1/72 scale once again. Unfortunately, I can no longer devote enough time to scale modeling, and 1/72 scale is the most efficient option within the limited time I can spare. This time, I started working on a model that I honestly can’t remember how it ended up in my hands. I had never built an SPG before, so this model did spark some excitement for me.

I began with the assembly stage. Almost none of the kit’s plastic parts fit properly. As you can see in the photos, I had to use a large amount of putty to fix the issues. Since there was no proper wheel spacing for the link-and-length tracks, fitting them into place was also extremely difficult.

Once the construction was finished, I moved on to painting. First, I primed the vehicle using Tamiya 87042 Gray Surface Primer, spraying a gray primer coat over the tank. You have to be very careful when using spray cans, because it’s hard to control the amount of paint or primer being applied. It’s very easy to end up with a coat that’s far too thick.

After the primer dried, I corrected the remaining visible flaws and moved on to painting. Instead of using an airbrush, I chose to apply the paint with a sponge. First, I used Vallejo Model Air 71093 OTAN Verde FS34094, dabbing the green paint over the entire tank with a sponge.

To begin modulating the color, I applied a lighter green using Vallejo Model Air 71137 U.S. Verde Claro FS34151, again with a sponge, covering almost the entire tank. This left the darker green in the recesses, while the upper surfaces became predominantly light green.

 

To push the modulation a bit further, I used the lighter green tone of Vallejo Model Air 71009 Eau de Nil Duck Egg Green. This time, I applied it only to the raised areas of the tank, focusing more heavily on the upper surfaces.

Finally, I loaded a brush with Vallejo Model Air 71321 IJA Light Grey Green and painted all the edges and raised details of the tank. This was essentially a highlighting step. With this application, I completed the green color modulation and moved on to painting the details.

As always, I started detailing with the tracks. I first painted them using Vallejo Model Air 71080 Rust as a base coat. Then, I applied Vallejo Model Air 71065 Steel to the areas that contact the ground and rub against the wheels, creating a metallic effect.

For the wooden parts of the tools on the tank, I used Vallejo Panzer Aces 70310 Old Wood. To make the wood look more realistic, I applied a wash using Tamiya Panel Liner Accent Color 87132 Brown. For the metallic parts, I first painted them with Vallejo Air 71315 Tyre Black and then dry-brushed with Vallejo Air 71065 Steel. For the exhaust, I started with Vallejo Model Air 71080 Rust and added soot effects to the exhaust outlet using Humbrol AV0004 Weathering Powder Smoke pigment.

Once the painting stage was complete, it was time to apply the decals included in the kit. First, I sprayed the tank with Vallejo 26517 Acrylic Gloss Varnish. Then I applied the decals and, at intervals, used Tamiya 87102 Mark Fit over them. After the decals were fully set and dry, I applied another coat of gloss varnish.

I didn’t apply any general oil-paint weathering to the tank. Instead, I went straight to pin washing using Winsor & Newton Lamp Black oil paint. To give the tank a dusty overall appearance, I washed the entire model using Winton Burnt Umber. This wash tended to accumulate slightly in the recessed areas.

After the oil paint had dried, I sealed the entire model with Vallejo 26518 Matt Acrylic Varnish. After the matte coat, the colors settled and blended a bit more. Once the matte varnish dried, I moved on to the weathering stage.

For weathering, I first applied chipping using AK Interactive AK711 Chipping Color with a sponge. I focused this application heavily on the edges. After that, I used a graphite pencil and a graffiti pencil to enhance the metallic effect on those same areas.

In the final weathering stage, I mixed Vallejo 73121 Desert Dust and Vallejo 73119 Europe Earth pigments with Cadence thinner and applied them to the model. Since the tank hadn’t seen heavy combat, I avoided excessive weathering. I finished the model in this state and placed it in the display case. It didn’t turn out to be a high-end model, but in the end, the goal is simply to enjoy the time spent building.